Close-range electrical inspection with a wide-angle radiometric thermal core: field of view, focus and emissivity
When a thermal camera has to work close to switchgear, a cabinet or a row of terminals, on a robot in a narrow aisle, on an arm, or fixed inside an enclosure, the standard lens shows too little and is often not sharp that close. A wide lens solves the first problem, but it changes pixel size, focus and how surfaces near the edge of the frame are measured. Here is what to work out, with MINI 640-2 Radiometric as the example. Coverage, pixel sizes and depths of field below are calculated.
Start with the distance you are allowed to work at
The closest working distance is usually set by the site’s electrical safety rules and the space in front of the equipment, not by the camera. Opening covers on energised equipment is arc-flash work: do it only as the site’s rules allow, with the required qualification, permit and protective equipment, or use inspection windows or a fixed camera instead. Fix the distance first; the lens follows from it.
How much one frame covers
| Lens and core | Field of view (H × V) | Area covered |
|---|---|---|
| 9.1 mm on 640 × 512 | 48.7° × 38.6° | About 1.09 × 0.84 m at 1.2 m, the near limit of its standard fixed-focus setting |
| 4 mm on 384 × 288 | 64.1° × 48.8° | About 0.63 × 0.45 m at 0.5 m; about 1.25 × 0.91 m at 1 m |
| 4 mm on 640 × 512 (non-standard) | About 100° × 82° | About 1.19 × 0.87 m at 0.5 m; about 2.38 × 1.74 m at 1 m |
Each side = 2 × distance × tan(half the field of view).
What the wide lens costs: pixel size
At the centre of the image a pixel covers IFOV × distance. A 4 mm lens gives about 3 mrad per pixel at the centre (12 μm ÷ 4 mm; the maker lists 3.05 mrad for its 4 mm lens on the 256 and 384 cores), so a pixel at the centre covers about 1.5 mm at 0.5 m and about 3 mm at 1 m. With the usual minimum of 3 × 3 pixels on a target, and provided the image is sharp at that distance, the smallest part you can measure at the centre is about 4.5 mm at 0.5 m and about 9 mm at 1 m (calculated). More pixels on the target is safer.
Towards the edges it gets coarser. The wide field of the 640 with this lens (about 100° × 82°) comes partly from barrel distortion, and a flat panel is seen at a slant near the edges, so near the left and right edges a pixel covers about 1.8 times as much of the panel horizontally as at the centre, and more in the corners (calculated from the about 100° × 82° field, assuming a smooth distortion curve). Keep the parts you must measure away from the edges of the frame.
One comparison is worth making before you choose. The 9.1 mm lens at 1.2 m and the 4 mm lens on the 640 at 0.5 m cover almost the same area with almost the same pixel size at the centre (about 1.6 mm and 1.5 mm, calculated), provided the wide lens is sharp at 0.5 m. If there is room to stand back 1.2 m, the standard lens does the job, with more even pixels and no steep viewing angles at the edges. The wide lens earns its place when there is less room than that, or when you need a whole panel in one frame from close up.
Focus: the near limit matters as much as the angle
These lenses are fixed focus. On MINI 640-2 Radiometric the standard 9.1 mm F1.1 lens is sharp from 1.2 to 5.5 m; the 4 mm F1.1 lens is listed as sharp from 0.29 m to infinity on the 256 × 192 and 384 × 288 cores. Both figures fit the usual depth-of-field formula with a total blur allowance of about two pixels (24 μm): the hyperfocal distance, f² ÷ (f-number × blur allowance), is about 3.1 m for the 9.1 mm lens and about 0.6 m for the 4 mm lens. Focused at about 2 m, the 9.1 mm lens is sharp from about 1.2 to 5.5 m; focused at about 0.6 m, the 4 mm lens is sharp from about 0.3 m to infinity (calculated). The hyperfocal distance grows with the square of the focal length, which is why a short lens can cover close and far at once and a 9.1 mm lens cannot.
Focus matters for the reading, not only the picture. A small hot spot out of focus spreads over more pixels, so its peak reading drops toward the background.
On MINI 640-2 Radiometric, the 4 mm lens is non-standard (built to order; samples ship within 15 working days of payment). Its f-number, factory focus setting and sharp range are not published, and a field about 100° × 82° wide is usually less sharp towards the corners than at the centre, so do not assume the 0.29 m figure above applies. Ask us for the sharp range at your closest working distance before you order.
Emissivity at close range
In a cabinet you see many surfaces at once. Paint, cable insulation and most plastics have emissivity around 0.9 or higher and read well. Bright copper and aluminium are very low (often below 0.1); bolts, lugs and oxidised metal vary widely, roughly 0.1 to 0.9, with surface condition. A reading on bare metal is unreliable even with the emissivity adjusted. Where a bare metal part matters, have qualified staff apply non-conductive, temperature-rated high-emissivity tape or paint while the equipment is isolated under the site’s procedure, then measure the patch with the emissivity set to its value (about 0.95 for matt black paint) and the reflected temperature set.
Angle matters too. For paints and plastics, emissivity stays close to its square-on value up to roughly 45° from perpendicular and falls at steeper angles. With the 640 and the 4 mm lens (about 100° × 82°) square-on to a flat panel, the left and right edges are viewed at about 50° and the corners at about 60°: another reason to keep important parts near the middle.
Shiny metal and glossy surfaces reflect. At close range the reflection can be a lamp, a person, or the warm parts of the robot or housing that carries the camera. Move the viewpoint a little: a real hot spot stays put, a reflection moves.
Load and comparison
A poor connection heats because of its resistance. Its heating power goes with the square of the current; in practice the temperature rise scales with the current to a power of about 1.6 to 2, so at half load it shows only about a quarter to a third of its full-load rise (calculated, steady state). Inspect under normal operating load, and record the load if you can. Compare like with like: the three phases of the same circuit, identical components under similar load. A difference between them often says more than an absolute value.
Closed doors and inspection windows
The camera sees the surface in front of it. It does not see through closed metal covers, and ordinary glass and acrylic block the 8–14 μm band. If a panel has an infrared inspection window, check that it is rated for 8–14 μm (calcium fluoride windows cut off part of that band), use its 8–14 μm transmission from the maker in your calculation, and check that the window opening does not cut off the edges of a wide field of view.
Range and ambient
Most connection and component heating sits in the low range of MINI 640-2 Radiometric (−20°C to 150°C); a severe fault can exceed 150°C, which the high range (100°C to 650°C) covers. Measurement is specified for −10°C to +70°C ambient, so check the temperature where the core will sit, including inside a warm enclosure in summer.
Checklist
- Closest allowed working distance, and the area you need in one frame
- Field of view and sharp range of the lens at that distance
- Pixel size at the centre and towards the edges, against your smallest part
- Emissivity of each surface, with tape or paint on bare metal you must measure
- Inspection under load, comparing like components
- Ambient temperature where the core sits
We sell MINI 640-2 Radiometric with a 9.1 mm lens as standard. Its 4 mm version (about 100° × 82°) is the same core, built and calibrated with the wider lens to order; samples ship within 15 working days of payment.
Related guides
Inspecting electrical equipment at close range?
Send the closest working distance, the area you need in one frame and the smallest part to measure. We reply within 24 hours on working days.