Imaging components. Procurement support.

Thermal core or complete thermal camera: what a 21 × 21 mm core does on its own, and what your product has to add

“Is it a camera, or only the module?” and “Can we put it straight on our network?” come up early in most new projects. A thermal core is the detector, the lens and the processing that turn heat into an image and, on a radiometric core, into temperatures. Most of what makes it a finished product is on your side. Here is the split, with MINI 640-2 Radiometric as the example.

What the core does on its own

  • Sees 8–14 μm infrared on a 640 × 512, 12 μm uncooled VOx detector, through the lens fitted to it
  • Processes the image, including non-uniformity correction (both shutter and shutterless correction are supported)
  • On the radiometric version, gives a calibrated temperature for every pixel, in two ranges: −20°C to 150°C and 100°C to 650°C
  • Sends image and temperature data over a digital interface, USB 2.0, MIPI (2-lane) or DVP depending on the version; control runs over UART, I²C or USB
  • Runs from a single 5 V supply at under 0.7 W (typical, USB output, 25°C), in a 21 × 21 × 10.3 mm body that weighs under 8.6 g without the lens

What it does not do

  • Protection: a bare core has no ingress rating. Rain, dust and condensation are handled by your enclosure, and the window in front of the lens must be an infrared material such as coated germanium, not glass.
  • Climate: measurement is specified for −10°C to +70°C ambient, imaging for −40°C to +80°C. Cold sites need a heater, and the sun should never sit in the field of view.
  • Recording: the core streams frames and does not record them. Storage is on the host.
  • Network: there is no Ethernet, PoE, RTSP or ONVIF on the core. If the camera has to appear on a network or in video-management software, a host computer does that.
  • Display: the radiometric version has digital outputs only. A monitor, HDMI or an analogue video transmitter needs a host or a converter.
  • Analytics and alarms: the core gives temperatures. Deciding what is too hot, logging it and raising an alarm is software on your side.
  • A visible image: the core sees heat only. If you need a normal picture as well, that is a second camera.

Where the work goes when you build on a core

  1. A carrier board: the 50-pin, 0.4 mm board-to-board connector, the 5 V supply and the interface you chose. For evaluation, the USB Type-C board that comes with the sample does this job.
  2. A host computer and software to receive the frames, run your logic and talk to the rest of your system. On the USB version, temperature readout and control go through TSDK, our SDK for this module, with builds for Linux (Ubuntu, Raspberry Pi and Jetson); it has been tested on our modules, comes at no extra charge and is provided after payment.
  3. An enclosure and window: sealing, a germanium window with the right coating, room for the lens’s field of view, and a path for heat away from the core.
  4. Checks on the finished product: readings through the window against a known reference, behaviour across your ambient range, and the approvals your market requires for the complete product.

When a complete camera is the better buy

If you need a few units on a network, in a weatherproof housing, feeding existing video-management software, buy a finished thermal network camera. Designing a core into a housing for that job takes longer than it saves.

When a core makes sense

  • Thermal imaging is part of your own product: a robot, a drone payload, an instrument, a monitoring unit.
  • Size, weight or power are tight. A 21 × 21 mm core drawing under 0.7 W (typical) is hard to match with a finished camera.
  • You want raw temperature data in your own software rather than in a vendor’s application.
  • You will build more than a handful, so the engineering is spread over many units.

A quick test

Write down what your product must do with the thermal data and where the data goes: a screen, a file, a network, an alarm. Everything on that list that is not “make an image” or “measure temperature” is your design work, whichever core you choose.

View MINI 640-2 Radiometric

Related guides

Building thermal imaging into your product?

Tell us what the product does with the thermal data and where the data goes. We reply within 24 hours on working days.

Discuss your requirements