# Thermal and Visible Camera Alignment: FOV and Parallax

Pairing a visible camera with a 640 × 512 thermal core: two windows, matching 5:4 to 4:3 or 16:9, parallax that changes with distance, alignment, timing.

Source: https://thermal.torsuntech.com/resources/thermal-visible-camera-alignment/

[Resources](https://thermal.torsuntech.com/resources/) / Thermal and visible

# Adding a visible camera next to a thermal core: field of view, parallax and alignment

“Can we see a normal picture too?” A thermal core shows heat, not colour or printed labels, so many products pair it with a visible camera. Done well, the two images line up and an operator sees at once which part is hot. Done carelessly, the hot spot lands beside the part. Here is what decides it, with MINI 640-2 Radiometric as the example. Offsets and angles below are calculated; lens data are from the maker’s manual.

## Two cameras, two windows

The thermal core sees 8–14 μm. Glass blocks that band, and germanium, the usual thermal window, is opaque to visible light. So a sealed housing normally has two windows side by side: germanium in front of the thermal lens, glass in front of the visible one. Materials that pass both bands, such as multispectral zinc sulphide, exist, but they cost more than a germanium and glass pair, transmit noticeably less above about 11 μm, and cannot take the DLC hard coating used on outdoor germanium windows without losing the visible band.

## Match the field of view, then crop

The thermal image is 5:4 (640 × 512). With the 9.1 mm lens it covers 48.7° × 38.6°. Most visible sensors are 4:3 or 16:9, so choose a visible lens that covers the thermal field in both directions, then crop:

- 4:3 sensor: about 50° horizontal or wider

- 16:9 sensor: about 64° horizontal or wider

In both cases the vertical 38.6° is the limit. Add the parallax angle at your closest distance (about 1.2° at 1.2 m with lenses 25 mm apart) in the direction the lenses are offset. These are simple rectilinear figures; lens distortion changes the edges, so check on real images. The visible camera usually has many more pixels: scale it to the thermal grid for overlays, or keep both and map coordinates between them.

## Parallax: the offset changes with distance

Two lenses side by side see the scene from two points. The angle between their views of one object is roughly the distance between the lens centres divided by the object distance. With the lens centres 25 mm apart:

- 9.1 mm thermal lens (1.3 mrad per pixel, sharp from 1.2 to 5.5 m): about 16 thermal pixels of offset at 1.2 m, about 3.5 at 5.5 m

- 13.5 mm thermal lens (0.9 mrad, non-standard on the radiometric 640): about 1.4 pixels at 20 m, under half a pixel beyond about 60 m

You can correct parallax exactly for one distance only. Align at 3 m with the 9.1 mm lens and the error elsewhere is the lens spacing × |1/R − 1/3 m|: about 3 pixels at 2 m and at 5.5 m, about 10 pixels at 1.2 m. So mount the two lenses as close together as you can (halving the spacing halves the error). Products that look tens of metres away can use one fixed alignment. Close-range products need a distance input, such as a rangefinder or a known working distance, to shift the overlay, or users who know to expect a few pixels of offset.

## Align with a target both cameras can see

A printed checkerboard barely shows in the thermal image: ink and paper have almost the same emissivity, and if you heat it with a lamp the pattern shows only briefly and blurs as the heat spreads. Use a target with contrast in both bands: a board with holes in front of a warm or cold background, or a pattern of painted and bare metal on a heated plate (paint has high emissivity, bare metal low). Capture it at several positions and fit the mapping from the matched points.

## Timing

The thermal core here runs at 30 Hz. The visible camera may run at 25, 30 or 60 Hz on its own clock. Stamp both streams on the host with the same clock, subtract each camera’s capture-to-arrival delay (measure it once, for example by filming a swinging warm object with both), and pair frames by time. On a moving platform, a difference in capture time shows up as an offset that alignment cannot remove.

## Keep temperatures from the thermal data

Blended images are for people to look at. Readings, alarms and logs should come from the thermal data itself, not from a fused picture.

## Before you design the housing

- Lens spacing, as small as practical

- A visible lens that covers the thermal field, with the crop worked out

- Your working distances, and how you will handle parallax across them

- An alignment target that shows in both bands

- Time stamps on both streams

- Two windows, or one multispectral window, sealed to the lenses

We supply the thermal core. The visible camera and the fusion are part of your design. The 13.5 mm lens is non-standard on the radiometric 640; samples with it ship within 15 working days of payment.

[View MINI 640-2 Radiometric](https://thermal.torsuntech.com/products/mini-640-2-radiometric/)

## Related guides

- [How wide, how far: choosing a lens for a 640 × 512 thermal core](https://thermal.torsuntech.com/resources/thermal-camera-lens-fov-distance/)

- [Thermal cores on patrol and inspection robots: typical specs, and what to check before you choose one](https://thermal.torsuntech.com/resources/thermal-camera-inspection-robot/)

- [Planning a robot’s thermal inspection route: viewpoints, stops and readings you can compare](https://thermal.torsuntech.com/resources/robot-thermal-inspection-route/)

## Planning a thermal and visible design?

Send the working distances, the visible camera you plan to use and the housing constraints. We reply within 24 hours on working days.

[Discuss your requirements](https://thermal.torsuntech.com/contact/)

---

TORSUN TECH · CATC Building 2, Shipai Town, Dongguan, Guangdong, China · info@torsuntech.com · Tel / WeChat / WhatsApp +86 180 2518 5996 · Enquiry: https://thermal.torsuntech.com/contact/
